Delete Trackpoint_380_breadboard.ino
This commit is contained in:
parent
d226082dd6
commit
af6e8b22da
1 changed files with 0 additions and 77 deletions
|
@ -1,77 +0,0 @@
|
||||||
/* Copyright 2020 Frank Adams
|
|
||||||
Licensed under the Apache License, Version 2.0 (the "License");
|
|
||||||
you may not use this file except in compliance with the License.
|
|
||||||
You may obtain a copy of the License at
|
|
||||||
http://www.apache.org/licenses/LICENSE-2.0
|
|
||||||
Unless required by applicable law or agreed to in writing, software
|
|
||||||
distributed under the License is distributed on an "AS IS" BASIS,
|
|
||||||
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
||||||
See the License for the specific language governing permissions and
|
|
||||||
limitations under the License.
|
|
||||||
*/
|
|
||||||
// This software interfaces the Teensy 3.2 with a Thinkpad 380ED laptop trackpoint.
|
|
||||||
// The trackpoint strain gauge resistors are fed to an instrumentation amplifier which drives the
|
|
||||||
// Teensy ADC inputs.
|
|
||||||
// In the Arduino IDE, select Tools, Teensy 3.2. Also under Tools, select Keyboard+Mouse+Joystick
|
|
||||||
//
|
|
||||||
// Revision History
|
|
||||||
// Rev 1.0 - April 22, 2020 - Original Release
|
|
||||||
//
|
|
||||||
// declare and initialize variables
|
|
||||||
int x_read; // stores the reading from the X ADC
|
|
||||||
int y_read; // same for the Y ADC
|
|
||||||
char mx; // signed byte used by the Mouse.move function for x value. Positive value moves to the right
|
|
||||||
char my; // positive y value moves down
|
|
||||||
int x_delta; // signed 16 bit value gives x movement amount
|
|
||||||
int y_delta; // y version.
|
|
||||||
int x_center; //resting position of x sensor
|
|
||||||
int y_center; //resting position of y sensor
|
|
||||||
int noise_zone = 50; // dead zone around the center. Can be as low as 3 but cursor may start to drift so add some safety margin.
|
|
||||||
// Increase this number if the cursor moves without touching the TP. Decrease if too much force is needed.
|
|
||||||
|
|
||||||
void setup()
|
|
||||||
{
|
|
||||||
delay(1000); // delay a second to let things settle out
|
|
||||||
analogReadRes(13); // set ADC resolution to 13 bits (16 bit ADC but low 3 bits are random noise)
|
|
||||||
analogReadAveraging(8); // ADC will take the average of 8 reads to filter noise.
|
|
||||||
x_center = analogRead(A10); // store the center (no movement) position for x
|
|
||||||
y_center = analogRead(A11); // same for y.
|
|
||||||
// When the keyboard code is added, detect when Fn - F8 is pushed to indicate that
|
|
||||||
// x_center and y_center should be read again from the ADC. This would be because
|
|
||||||
// the operator notices the cursor is moving without being pushed.
|
|
||||||
}
|
|
||||||
//
|
|
||||||
// ************************************Main Loop***************************************************************
|
|
||||||
void loop() {
|
|
||||||
mx = 0; // for each loop, start with zero and update only if movement detected
|
|
||||||
my = 0; // same for y
|
|
||||||
|
|
||||||
x_read = analogRead(A10); // read the ADC tied to the X sensor
|
|
||||||
if (x_read > (x_center + noise_zone)) { // is ADC to the right of the noise zone beyond the resting position?
|
|
||||||
x_delta = (x_read - (x_center + noise_zone)) / 10; // find out how far beyond noise zone. Divide by 10 to slow it down.
|
|
||||||
mx = byte(x_delta); // convert signed 16 bit to signed 8 bit
|
|
||||||
}
|
|
||||||
else if (x_read < (x_center - noise_zone)) { // is ADC to the left of the noise zone beyond the resting position?
|
|
||||||
x_delta = (((x_center - noise_zone) - x_read) / 10) * -1; // Answer should be negative so multiply by -1
|
|
||||||
mx = byte(x_delta);
|
|
||||||
}
|
|
||||||
|
|
||||||
y_read = analogRead(A11); // read the ADC tied to the Y sensor
|
|
||||||
if (y_read > (y_center + noise_zone)) {
|
|
||||||
y_delta = ((y_read - (y_center + noise_zone)) / 10) * -1; // up movement is negative for Mouse.move function
|
|
||||||
my = byte(y_delta);
|
|
||||||
}
|
|
||||||
else if (y_read < (y_center - noise_zone)) {
|
|
||||||
y_delta = (((y_center - noise_zone) - y_read) / 10);
|
|
||||||
my = byte(y_delta);
|
|
||||||
}
|
|
||||||
|
|
||||||
// send the x and y data over usb if either one is not at center position
|
|
||||||
if ((mx != 0x00) || (my != 0x00)) {
|
|
||||||
Mouse.move(mx,my);
|
|
||||||
}
|
|
||||||
//
|
|
||||||
// **************************************End of trackpoint routine***********************************
|
|
||||||
//
|
|
||||||
delay(30); // wait 30ms before repeating next polling cycle
|
|
||||||
}
|
|
Loading…
Reference in a new issue