Delete Touchpad_LC.ino
This commit is contained in:
Frank Adams
GitHub
parent
5f66e125f2
commit
c01c69fc3a
1 changed files with 0 additions and 360 deletions
|
|
@ -1,360 +0,0 @@
|
||||||
/* Copyright 2019 Frank Adams
|
|
||||||
Licensed under the Apache License, Version 2.0 (the "License");
|
|
||||||
you may not use this file except in compliance with the License.
|
|
||||||
You may obtain a copy of the License at
|
|
||||||
http://www.apache.org/licenses/LICENSE-2.0
|
|
||||||
Unless required by applicable law or agreed to in writing, software
|
|
||||||
distributed under the License is distributed on an "AS IS" BASIS,
|
|
||||||
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
||||||
See the License for the specific language governing permissions and
|
|
||||||
limitations under the License.
|
|
||||||
*/
|
|
||||||
// This software interfaces the Teensy LC with the 3.3v PS/2 touchpad found in an HP DV9000 laptop.
|
|
||||||
// WARNING: THE TEENSY LC NEEDS CLOCK AND DATA LEVEL TRANSLATORS TO INTERFACE WITH A 5V TOUCHPAD.
|
|
||||||
// The ps/2 code uses the USB PJRC Mouse functions at www.pjrc.com/teensy/td_mouse.html
|
|
||||||
// The ps/2 code has a watchdog timer so the code can't hang if a clock edge is missed.
|
|
||||||
// In the Arduino IDE, select Tools, Teensy LC. Also under Tools, select Keyboard+Mouse+Joystick
|
|
||||||
//
|
|
||||||
// Revision History
|
|
||||||
// Rev 1.0 - Nov 23, 2018 - Original Release
|
|
||||||
// Rev 1.1 - Dec 2, 2018 - Replaced ps/2 trackpoint code from playground arduino with my own code
|
|
||||||
// Rev 1.2 - Feb 2, 2019 - Changed the error routine and added an error LED
|
|
||||||
// Rev 1.3 - Feb 14, 2019 - Changed the comments and I/O pins for the Teensy LC
|
|
||||||
//
|
|
||||||
// This code has been tested on the touchpad from an HP DV9000 touchpad
|
|
||||||
// Touchpad part number 920-000702-04 Rev A
|
|
||||||
// The test points on the touchpad were wired as follows:
|
|
||||||
// T22 = 3.3V
|
|
||||||
// T23 = Gnd (I soldered to the ground plane)
|
|
||||||
// T10 = Clock
|
|
||||||
// T11 = Data
|
|
||||||
// This touchpad has active pullups so no additional pullups were required.
|
|
||||||
//
|
|
||||||
// The touchpad ps/2 data and clock lines are connected to the following Teensy I/O pins
|
|
||||||
#define TP_DATA 20 // modify these I/O's to match your jumpers
|
|
||||||
#define TP_CLK 18
|
|
||||||
// Teensy LED will be lit if the touchpad fails to respond properly during initialization
|
|
||||||
#define ERROR_LED 13
|
|
||||||
//
|
|
||||||
// Declare variable that will be used by functions
|
|
||||||
boolean touchpad_error = LOW; // sent high when touch pad routine times out
|
|
||||||
//
|
|
||||||
// Function to set a pin to high impedance (acts like open drain output)
|
|
||||||
void go_z(int pin)
|
|
||||||
{
|
|
||||||
pinMode(pin, INPUT);
|
|
||||||
digitalWrite(pin, HIGH);
|
|
||||||
}
|
|
||||||
//
|
|
||||||
// Function to set a pin as an input with a pullup
|
|
||||||
void go_pu(int pin)
|
|
||||||
{
|
|
||||||
pinMode(pin, INPUT_PULLUP);
|
|
||||||
digitalWrite(pin, HIGH);
|
|
||||||
}
|
|
||||||
//
|
|
||||||
// Function to send a pin to a logic low
|
|
||||||
void go_0(int pin)
|
|
||||||
{
|
|
||||||
pinMode(pin, OUTPUT);
|
|
||||||
digitalWrite(pin, LOW);
|
|
||||||
}
|
|
||||||
//
|
|
||||||
// Function to send a pin to a logic high
|
|
||||||
void go_1(int pin)
|
|
||||||
{
|
|
||||||
pinMode(pin, OUTPUT);
|
|
||||||
digitalWrite(pin, HIGH);
|
|
||||||
}
|
|
||||||
//
|
|
||||||
// *****************Functions for Touchpad***************************
|
|
||||||
//
|
|
||||||
// Function to send the touchpad a byte of data (command)
|
|
||||||
//
|
|
||||||
void tp_write(char send_data)
|
|
||||||
{
|
|
||||||
unsigned int timeout = 200; // breakout of loop if over this value in msec
|
|
||||||
elapsedMillis watchdog; // zero the watchdog timer clock
|
|
||||||
char odd_parity = 0; // clear parity bit count
|
|
||||||
// Enable the bus by floating the clock and data
|
|
||||||
go_pu(TP_CLK); //
|
|
||||||
go_pu(TP_DATA); //
|
|
||||||
delayMicroseconds(250); // wait before requesting the bus
|
|
||||||
go_0(TP_CLK); // Send the Clock line low to request to transmit data
|
|
||||||
delayMicroseconds(100); // wait for 100 microseconds per bus spec
|
|
||||||
go_0(TP_DATA); // Send the Data line low (the start bit)
|
|
||||||
delayMicroseconds(1); //
|
|
||||||
go_pu(TP_CLK); // Release the Clock line so it is pulled high
|
|
||||||
delayMicroseconds(1); // give some time to let the clock line go high
|
|
||||||
while (digitalRead(TP_CLK) == HIGH) { // loop until the clock goes low
|
|
||||||
if (watchdog >= timeout) { //check for infinite loop
|
|
||||||
break; // break out of infinite loop
|
|
||||||
}
|
|
||||||
}
|
|
||||||
// send the 8 bits of send_data
|
|
||||||
for (int j=0; j<8; j++) {
|
|
||||||
if (send_data & 1) { //check if lsb is set
|
|
||||||
go_pu(TP_DATA); // send a 1 to TP
|
|
||||||
odd_parity = odd_parity + 1; // keep running total of 1's sent
|
|
||||||
}
|
|
||||||
else {
|
|
||||||
go_0(TP_DATA); // send a 0 to TP
|
|
||||||
}
|
|
||||||
delayMicroseconds(1); // delay to let the clock settle out
|
|
||||||
while (digitalRead(TP_CLK) == LOW) { // loop until the clock goes high
|
|
||||||
if (watchdog >= timeout) { //check for infinite loop
|
|
||||||
break; // break out of infinite loop
|
|
||||||
}
|
|
||||||
}
|
|
||||||
delayMicroseconds(1); // delay to let the clock settle out
|
|
||||||
while (digitalRead(TP_CLK) == HIGH) { // loop until the clock goes low
|
|
||||||
if (watchdog >= timeout) { //check for infinite loop
|
|
||||||
break; // break out of infinite loop
|
|
||||||
}
|
|
||||||
}
|
|
||||||
send_data = send_data >> 1; // shift data right by 1 to prepare for next loop
|
|
||||||
}
|
|
||||||
// send the parity bit
|
|
||||||
if (odd_parity & 1) { //check if lsb of parity is set
|
|
||||||
go_0(TP_DATA); // already odd so send a 0 to TP
|
|
||||||
}
|
|
||||||
else {
|
|
||||||
go_pu(TP_DATA); // send a 1 to TP to make parity odd
|
|
||||||
}
|
|
||||||
delayMicroseconds(1); // delay to let the clock settle out
|
|
||||||
while (digitalRead(TP_CLK) == LOW) { // loop until the clock goes high
|
|
||||||
if (watchdog >= timeout) { //check for infinite loop
|
|
||||||
break; // break out of infinite loop
|
|
||||||
}
|
|
||||||
}
|
|
||||||
delayMicroseconds(1); // delay to let the clock settle out
|
|
||||||
while (digitalRead(TP_CLK) == HIGH) { // loop until the clock goes low
|
|
||||||
if (watchdog >= timeout) { //check for infinite loop
|
|
||||||
break; // break out of infinite loop
|
|
||||||
}
|
|
||||||
}
|
|
||||||
go_pu(TP_DATA); // Release the Data line so it goes high as the stop bit
|
|
||||||
delayMicroseconds(80); // testing shows delay at least 40us
|
|
||||||
while (digitalRead(TP_CLK) == HIGH) { // loop until the clock goes low
|
|
||||||
if (watchdog >= timeout) { //check for infinite loop
|
|
||||||
break; // break out of infinite loop
|
|
||||||
}
|
|
||||||
}
|
|
||||||
delayMicroseconds(1); // wait to let the data settle
|
|
||||||
if (digitalRead(TP_DATA)) { // Ack bit s/b low if good transfer
|
|
||||||
}
|
|
||||||
while ((digitalRead(TP_CLK) == LOW) || (digitalRead(TP_DATA) == LOW)) { // loop if clock or data are low
|
|
||||||
if (watchdog >= timeout) { //check for infinite loop
|
|
||||||
break; // break out of infinite loop
|
|
||||||
}
|
|
||||||
}
|
|
||||||
// Inhibit the bus so the tp only talks when we're listening
|
|
||||||
go_0(TP_CLK);
|
|
||||||
}
|
|
||||||
//
|
|
||||||
// Function to get a byte of data from the touchpad
|
|
||||||
//
|
|
||||||
char tp_read(void)
|
|
||||||
{
|
|
||||||
unsigned int timeout = 200; // breakout of loop if over this value in msec
|
|
||||||
elapsedMillis watchdog; // zero the watchdog timer clock
|
|
||||||
char rcv_data = 0; // initialize to zero
|
|
||||||
char mask = 1; // shift a 1 across the 8 bits to select where to load the data
|
|
||||||
char rcv_parity = 0; // count the ones received
|
|
||||||
go_pu(TP_CLK); // release the clock
|
|
||||||
go_pu(TP_DATA); // release the data
|
|
||||||
delayMicroseconds(5); // delay to let clock go high
|
|
||||||
while (digitalRead(TP_CLK) == HIGH) { // loop until the clock goes low
|
|
||||||
if (watchdog >= timeout) { //check for infinite loop
|
|
||||||
break; // break out of infinite loop
|
|
||||||
}
|
|
||||||
}
|
|
||||||
if (digitalRead(TP_DATA)) { // Start bit s/b low from tp
|
|
||||||
// start bit not correct - put error handler here if desired
|
|
||||||
}
|
|
||||||
delayMicroseconds(1); // delay to let the clock settle out
|
|
||||||
while (digitalRead(TP_CLK) == LOW) { // loop until the clock goes high
|
|
||||||
if (watchdog >= timeout) { //check for infinite loop
|
|
||||||
break; // break out of infinite loop
|
|
||||||
}
|
|
||||||
}
|
|
||||||
for (int k=0; k<8; k++) {
|
|
||||||
delayMicroseconds(1); // delay to let the clock settle out
|
|
||||||
while (digitalRead(TP_CLK) == HIGH) { // loop until the clock goes low
|
|
||||||
if (watchdog >= timeout) { //check for infinite loop
|
|
||||||
break; // break out of infinite loop
|
|
||||||
}
|
|
||||||
}
|
|
||||||
if (digitalRead(TP_DATA)) { // check if data is high
|
|
||||||
rcv_data = rcv_data | mask; // set the appropriate bit in the rcv data
|
|
||||||
rcv_parity++; // increment the parity bit counter
|
|
||||||
}
|
|
||||||
mask = mask << 1;
|
|
||||||
delayMicroseconds(1); // delay to let the clock settle out
|
|
||||||
while (digitalRead(TP_CLK) == LOW) { // loop until the clock goes high
|
|
||||||
if (watchdog >= timeout) { //check for infinite loop
|
|
||||||
break; // break out of infinite loop
|
|
||||||
}
|
|
||||||
}
|
|
||||||
}
|
|
||||||
// receive parity
|
|
||||||
delayMicroseconds(1); // delay to let the clock settle out
|
|
||||||
while (digitalRead(TP_CLK) == HIGH) { // loop until the clock goes low
|
|
||||||
if (watchdog >= timeout) { //check for infinite loop
|
|
||||||
break; // break out of infinite loop
|
|
||||||
}
|
|
||||||
}
|
|
||||||
if (digitalRead(TP_DATA)) { // check if received parity is high
|
|
||||||
rcv_parity++; // increment the parity bit counter
|
|
||||||
}
|
|
||||||
rcv_parity = rcv_parity & 1; // mask off all bits except the lsb
|
|
||||||
if (rcv_parity == 0) { // check for bad (even) parity
|
|
||||||
// bad parity - pass to future error handler
|
|
||||||
}
|
|
||||||
delayMicroseconds(1); // delay to let the clock settle out
|
|
||||||
while (digitalRead(TP_CLK) == LOW) { // loop until the clock goes high
|
|
||||||
if (watchdog >= timeout) { //check for infinite loop
|
|
||||||
break; // break out of infinite loop
|
|
||||||
}
|
|
||||||
}
|
|
||||||
// stop bit
|
|
||||||
delayMicroseconds(1); // delay to let the clock settle out
|
|
||||||
while (digitalRead(TP_CLK) == HIGH) { // loop until the clock goes low
|
|
||||||
if (watchdog >= timeout) { //check for infinite loop
|
|
||||||
break; // break out of infinite loop
|
|
||||||
}
|
|
||||||
}
|
|
||||||
if (digitalRead(TP_DATA) == LOW) { // check if stop bit is bad (low)
|
|
||||||
// send bad stop bit to future error handler
|
|
||||||
}
|
|
||||||
delayMicroseconds(1); // delay to let the clock settle out
|
|
||||||
while (digitalRead(TP_CLK) == LOW) { // loop until the clock goes high
|
|
||||||
if (watchdog >= timeout) { //check for infinite loop
|
|
||||||
break; // break out of infinite loop
|
|
||||||
}
|
|
||||||
}
|
|
||||||
// Inhibit the bus so the tp only talks when we're listening
|
|
||||||
go_0(TP_CLK);
|
|
||||||
return rcv_data; // pass the received data back
|
|
||||||
}
|
|
||||||
//
|
|
||||||
void touchpad_init()
|
|
||||||
{
|
|
||||||
touchpad_error = LOW; // start with no error
|
|
||||||
go_pu(TP_CLK); // float the clock and data to touchpad
|
|
||||||
go_pu(TP_DATA);
|
|
||||||
// Sending reset command to touchpad
|
|
||||||
tp_write(0xff);
|
|
||||||
if (tp_read() != 0xfa) { // verify correct ack byte
|
|
||||||
touchpad_error = HIGH;
|
|
||||||
}
|
|
||||||
delay(350); // wait 350ms so tp can run its self diagnostic
|
|
||||||
// verify proper response from tp
|
|
||||||
if (tp_read() != 0xaa) { // verify basic assurance test passed
|
|
||||||
touchpad_error = HIGH;
|
|
||||||
}
|
|
||||||
if (tp_read() != 0x00) { // verify basic assurance test passed
|
|
||||||
touchpad_error = HIGH;
|
|
||||||
}
|
|
||||||
// increase resolution from 4 counts/mm to 8 counts/mm
|
|
||||||
tp_write(0xe8); // Sending resolution command
|
|
||||||
if (tp_read() != 0xfa) { // verify correct ack byte
|
|
||||||
touchpad_error = HIGH;
|
|
||||||
}
|
|
||||||
tp_write(0x03); // value of 03 = 8 counts/mm resolution (default is 4 counts/mm)
|
|
||||||
if (tp_read() != 0xfa) { // verify correct ack byte
|
|
||||||
touchpad_error = HIGH;
|
|
||||||
}
|
|
||||||
// Sending remote mode code so the touchpad will send data only when polled
|
|
||||||
tp_write(0xf0); // remote mode
|
|
||||||
if (tp_read() != 0xfa) { // verify correct ack byte
|
|
||||||
touchpad_error = HIGH;
|
|
||||||
}
|
|
||||||
}
|
|
||||||
// ************************************Begin Routine*********************************************************
|
|
||||||
void setup()
|
|
||||||
{
|
|
||||||
touchpad_init(); // reset touchpad, then set it's resolution and put it in remote mode
|
|
||||||
pinMode(ERROR_LED, OUTPUT); // define teensy I/O 13 as an output
|
|
||||||
}
|
|
||||||
|
|
||||||
// declare and initialize variables
|
|
||||||
char mstat; // touchpad status reg = Y overflow, X overflow, Y sign bit, X sign bit, Always 1, Middle Btn, Right Btn, Left Btn
|
|
||||||
char mx; // touchpad x movement = 8 data bits. The sign bit is in the status register to
|
|
||||||
// make a 9 bit 2's complement value. Left to right on the touchpad gives a positive value.
|
|
||||||
char my; // touchpad y movement also 8 bits plus sign. Touchpad movement away from the user gives a positive value.
|
|
||||||
boolean over_flow; // set if x or y movement values are bad due to overflow
|
|
||||||
boolean left_button = 0; // on/off variable for left button = bit 0 of mstat
|
|
||||||
boolean right_button = 0; // on/off variable for right button = bit 1 of mstat
|
|
||||||
boolean old_left_button = 0; // on/off variable for left button status the previous polling cycle
|
|
||||||
boolean old_right_button = 0; // on/off variable for right button status the previous polling cycle
|
|
||||||
boolean button_change = 0; // Active high, shows when a touchpad left or right button has changed since last polling cycle
|
|
||||||
|
|
||||||
// ************************************Main Loop***************************************************************
|
|
||||||
void loop() {
|
|
||||||
if (touchpad_error == LOW) { // check if touchpad is present
|
|
||||||
digitalWrite(ERROR_LED, LOW); // turn off LED on Teensy to show touchpad initialized OK
|
|
||||||
// poll the touchpad for new movement data
|
|
||||||
over_flow = 0; // assume no overflow until status is received
|
|
||||||
tp_write(0xeb); // request data
|
|
||||||
if (tp_read() != 0xfa) { // verify correct ack byte
|
|
||||||
// bad ack - pass to future error handler
|
|
||||||
}
|
|
||||||
mstat = tp_read(); // save into status variable
|
|
||||||
mx = tp_read(); // save into x variable
|
|
||||||
my = tp_read(); // save into y variable
|
|
||||||
if (((0x80 & mstat) == 0x80) || ((0x40 & mstat) == 0x40)) { // x or y overflow bits set?
|
|
||||||
over_flow = 1; // set the overflow flag
|
|
||||||
}
|
|
||||||
// change the x data from 9 bit to 8 bit 2's complement
|
|
||||||
mx = mx & 0x7f; // mask off 8th bit
|
|
||||||
if ((0x10 & mstat) == 0x10) { // move the sign into
|
|
||||||
mx = 0x80 | mx; // the 8th bit position
|
|
||||||
}
|
|
||||||
// change the y data from 9 bit to 8 bit 2's complement and then take the 2's complement
|
|
||||||
// because y movement on ps/2 format is opposite of touchpad.move function
|
|
||||||
my = my & 0x7f; // mask off 8th bit
|
|
||||||
if ((0x20 & mstat) == 0x20) { // move the sign into
|
|
||||||
my = 0x80 | my; // the 8th bit position
|
|
||||||
}
|
|
||||||
my = (~my + 0x01); // change the sign of y data by taking the 2's complement (invert and add 1)
|
|
||||||
// zero out mx and my if over_flow or touchpad_error is set
|
|
||||||
if ((over_flow) || (touchpad_error)) {
|
|
||||||
mx = 0x00; // data is garbage so zero it out
|
|
||||||
my = 0x00;
|
|
||||||
}
|
|
||||||
// send the x and y data back via usb if either one is non-zero
|
|
||||||
if ((mx != 0x00) || (my != 0x00)) {
|
|
||||||
Mouse.move(mx,my);
|
|
||||||
}
|
|
||||||
//
|
|
||||||
// send the touchpad left and right button status over usb if no error
|
|
||||||
if ((0x01 & mstat) == 0x01) { // if left button set
|
|
||||||
left_button = 1;
|
|
||||||
}
|
|
||||||
else { // clear left button
|
|
||||||
left_button = 0;
|
|
||||||
}
|
|
||||||
if ((0x02 & mstat) == 0x02) { // if right button set
|
|
||||||
right_button = 1;
|
|
||||||
}
|
|
||||||
else { // clear right button
|
|
||||||
right_button = 0;
|
|
||||||
}
|
|
||||||
// Determine if the left or right touch pad buttons have changed since last polling cycle
|
|
||||||
button_change = (left_button ^ old_left_button) | (right_button ^ old_right_button);
|
|
||||||
// Don't send button status if there's no change since last time.
|
|
||||||
if (button_change){
|
|
||||||
Mouse.set_buttons(left_button, 0, right_button); // send button status
|
|
||||||
}
|
|
||||||
old_left_button = left_button; // remember new button status for next polling cycle
|
|
||||||
old_right_button = right_button;
|
|
||||||
}
|
|
||||||
else {
|
|
||||||
digitalWrite(ERROR_LED, HIGH);
|
|
||||||
}
|
|
||||||
//
|
|
||||||
// **************************************End of touchpad routine***********************************
|
|
||||||
//
|
|
||||||
delay(30); // wait 30ms before repeating next polling cycle
|
|
||||||
}
|
|
||||||
Loading…
Reference in a new issue