diff --git a/Example_Keyboards/HP_ZV6000/HP Keyboard Matrix.docx b/Example_Keyboards/HP_ZV6000/HP Keyboard Matrix.docx
new file mode 100644
index 0000000..8fb207d
Binary files /dev/null and b/Example_Keyboards/HP_ZV6000/HP Keyboard Matrix.docx differ
diff --git a/Example_Keyboards/HP_ZV6000/HP_ZV6000.ino b/Example_Keyboards/HP_ZV6000/HP_ZV6000.ino
new file mode 100644
index 0000000..17fe4dc
--- /dev/null
+++ b/Example_Keyboards/HP_ZV6000/HP_ZV6000.ino
@@ -0,0 +1,405 @@
+/* Copyright 2020 Frank Adams
+   Licensed under the Apache License, Version 2.0 (the "License");
+   you may not use this file except in compliance with the License.
+   You may obtain a copy of the License at
+       http://www.apache.org/licenses/LICENSE-2.0
+   Unless required by applicable law or agreed to in writing, software
+   distributed under the License is distributed on an "AS IS" BASIS,
+   WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+   See the License for the specific language governing permissions and
+   limitations under the License.
+*/
+// This software implements a HP ZV6000 Laptop Keyboard Controller using a Teensy LC on 
+// a daughterboard with a 24 pin FPC connector. The keyboard has an Italian layout.
+// This routine uses the Teensyduino "Micro-Manager Method" to send Normal and Modifier 
+// keys over USB. Multi-media keys are sent with keyboard press and release functions.
+// Description of Teensyduino keyboard functions is at www.pjrc.com/teensy/td_keyboard.html
+// 
+// Revision History
+// Original Release Oct 24, 2020
+// Rev A Oct 25, 2020 - Fixed keys that did not respond
+//
+// Compile with tools --> keyboared layout: Italian
+#define MODIFIERKEY_FN 0x8f   // give Fn key a HID code Lock
+//
+const byte rows_max = 16; // sets the number of rows in the matrix
+const byte cols_max = 8; // sets the number of columns in the matrix
+// 
+// Load the normal key matrix with the Teensyduino key names described at www.pjrc.com/teensy/td_keyboard.html
+// A zero indicates no normal key at that location.
+// The Italian vowel grave keys are listed in the LAYOUT_ITALIAN section of the keylayouts.h file located at:
+// C:\Program Files (x86)\Arduino\hardware\teensy\avr\cores\teensy3  
+// 
+/* Notes from Luigi
+For a non-US keyboard, look at the file keylayouts.h under the desired language and find the desired key, then use the corresponding US key name.
+Example for the quote ' character on the Italian keyboard, you will find the quote in the comment
+#define ASCII_27 KEY_MINUS // 39 '
+thus, into the normal keys array, where the quote would go, you insert KEY_MINUS
+Example for the + key on the Italian keyboard, you will find the + in the comment
+#define ASCII_2B KEY_RIGHT_BRACE // 43 +
+thus you must use KEY_RIGHT_BRACE where + would go. Do this for all other special keys.
+The backslash is not listed because it seems it is a unique character but once you know the ASCII code is 92, 
+you can use the US key with the same ASCII code. The tilde key has ASCII code 92.
+#define ASCII_5C KEY_TILDE // 92.
+The "less than key" < also known as "angular braces key" doesn't work like the other keys. Using KEY_NON_US_100 did not have any effect on the output. 
+To make it work, this key is intercepted in the code and the correct literal is sent using Keyboard.press(). 
+Look at lines 365 to 377 for < and > key coding.
+*/
+//
+int normal[rows_max][cols_max] = {
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{KEY_F7,KEY_W,KEY_2,KEY_S,KEY_X,KEY_F6,KEY_F5,KEY_F8},
+{KEY_ESC,KEY_Q,KEY_1,KEY_A,KEY_Z,KEY_TAB,KEY_TILDE,KEY_CAPS_LOCK},
+{KEY_F4,KEY_E,KEY_3,KEY_D,KEY_C,KEY_F3,KEY_F2,KEY_F1},
+{KEY_G,KEY_R,KEY_4,KEY_F,KEY_V,KEY_T,KEY_5,KEY_B},
+{0,0,0,0,0,0,0,0},
+{KEY_H,KEY_U,KEY_7,KEY_J,KEY_M,KEY_Y,KEY_6,KEY_N},
+{KEY_SCROLL_LOCK,KEY_I,KEY_8,KEY_K,KEY_COMMA,KEY_RIGHT_BRACE,KEY_NON_US_100,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,KEY_MENU,0},
+{0,0,0,0,0,0,0,0},
+{KEY_BACKSPACE,KEY_UP,KEY_DOWN,KEY_ENTER,KEY_SPACE,0,ISO_8859_1_F9,KEY_PAUSE},
+{KEY_F11,KEY_O,KEY_9,KEY_L,KEY_PERIOD,KEY_F10,KEY_F9,KEY_F12},
+{ISO_8859_1_E0,KEY_P,KEY_0,ISO_8859_1_F2,KEY_SLASH,ISO_8859_1_E8,KEY_MINUS,ISO_8859_1_EC},
+{KEY_INSERT,KEY_LEFT,KEY_RIGHT,KEY_PAGE_DOWN,KEY_END,KEY_HOME,KEY_PAGE_UP,KEY_DELETE}
+};
+//
+// Load the modifier key matrix with key names at the correct row-column location. 
+// A zero indicates no modifier key at that location.
+int modifier[rows_max][cols_max] = {
+{0,MODIFIERKEY_RIGHT_SHIFT,0,0,MODIFIERKEY_LEFT_SHIFT,0,0,0},
+{0,0,0,MODIFIERKEY_RIGHT_CTRL,0,MODIFIERKEY_LEFT_CTRL,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,MODIFIERKEY_FN,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{MODIFIERKEY_GUI,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,MODIFIERKEY_LEFT_ALT,0,0,0,0,MODIFIERKEY_RIGHT_ALT},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0}
+};
+// Load the media key matrix with Fn key names at the correct row-column location. 
+// A zero indicates no media key at that location.
+int media[rows_max][cols_max] = {
+  {0,0,0,0,0,0,0,0},
+  {0,0,0,0,0,0,0,0},
+  {KEY_MEDIA_VOLUME_DEC,0,0,0,0,0,0,KEY_MEDIA_VOLUME_INC},
+  {0,0,0,0,0,0,0,0},
+  {0,0,0,0,0,0,0,0},
+  {0,0,0,0,0,0,0,0},
+  {0,0,0,0,0,0,0,0},
+  {0,0,0,0,0,0,0,0},
+  {KEY_NUM_LOCK,0,0,0,0,0,0,0},
+  {0,0,0,0,0,0,0,0},
+  {0,0,0,0,0,0,0,0},
+  {0,0,0,0,0,0,0,0},
+  {0,0,0,0,0,0,0,KEY_PRINTSCREEN},
+  {0,0,0,0,0,0,0,0},
+  {0,0,0,0,0,0,0,0},
+  {0,0,0,0,0,0,0,0}
+};  
+//
+// Initialize the old_key matrix with one's. 
+// 1 = key not pressed, 0 = key is pressed
+boolean old_key[rows_max][cols_max] = {
+  {1,1,1,1,1,1,1,1},
+  {1,1,1,1,1,1,1,1},
+  {1,1,1,1,1,1,1,1},
+  {1,1,1,1,1,1,1,1},
+  {1,1,1,1,1,1,1,1},
+  {1,1,1,1,1,1,1,1},
+  {1,1,1,1,1,1,1,1},
+  {1,1,1,1,1,1,1,1},
+  {1,1,1,1,1,1,1,1},
+  {1,1,1,1,1,1,1,1},
+  {1,1,1,1,1,1,1,1},
+  {1,1,1,1,1,1,1,1},
+  {1,1,1,1,1,1,1,1},
+  {1,1,1,1,1,1,1,1},
+  {1,1,1,1,1,1,1,1},
+  {1,1,1,1,1,1,1,1}
+};
+//
+// Define the Teensy LC I/O numbers (translated from the FPC pin #)
+//
+int Row_IO[rows_max] = {1,21,4,20,19,6,18,7,17,8,16,9,15,10,14,11}; // Teensy LC I/O numbers for rows
+//
+int Col_IO[cols_max] = {23,0,22,24,2,3,25,5}; // Teensy LC I/O numbers for columns
+//
+// Declare variables that will be used by functions
+boolean slots_full = LOW; // Goes high when slots 1 thru 6 contain normal keys
+// slot 1 thru slot 6 hold the normal key values to be sent over USB. 
+int slot1 = 0; //value of 0 means the slot is empty and can be used.  
+int slot2 = 0; 
+int slot3 = 0; 
+int slot4 = 0; 
+int slot5 = 0; 
+int slot6 = 0;
+//
+int mod_shift_l = 0; // These variables are sent over USB as modifier keys.
+int mod_shift_r = 0; // Each is either set to 0 or MODIFIER_ ... 
+int mod_ctrl_l = 0;   
+int mod_ctrl_r = 0;
+int mod_alt_l = 0;
+int mod_alt_r = 0;
+int mod_gui = 0;
+//
+// Function to load the key name into the first available slot
+void load_slot(int key) {
+  if (!slot1)  {
+    slot1 = key;
+  }
+  else if (!slot2) {
+    slot2 = key;
+  }
+  else if (!slot3) {
+    slot3 = key;
+  }
+  else if (!slot4) {
+    slot4 = key;
+  }
+  else if (!slot5) {
+    slot5 = key;
+  }
+  else if (!slot6) {
+    slot6 = key;
+  }
+  if (!slot1 || !slot2 || !slot3 || !slot4 || !slot5 || !slot6)  {
+    slots_full = LOW; // slots are not full
+  }
+  else {
+    slots_full = HIGH; // slots are full
+  } 
+}
+//
+// Function to clear the slot that contains the key name
+void clear_slot(int key) {
+  if (slot1 == key) {
+    slot1 = 0;
+  }
+  else if (slot2 == key) {
+    slot2 = 0;
+  }
+  else if (slot3 == key) {
+    slot3 = 0;
+  }
+  else if (slot4 == key) {
+    slot4 = 0;
+  }
+  else if (slot5 == key) {
+    slot5 = 0;
+  }
+  else if (slot6 == key) {
+    slot6 = 0;
+  }
+  if (!slot1 || !slot2 || !slot3 || !slot4 || !slot5 || !slot6)  {
+    slots_full = LOW; // slots are not full
+  }
+  else {
+    slots_full = HIGH; // slots are full
+  } 
+}
+//
+// Function to load the modifier key name into the appropriate mod variable
+void load_mod(int m_key) {
+  if (m_key == MODIFIERKEY_LEFT_SHIFT)  {
+    mod_shift_l = m_key;
+  }
+  else if (m_key == MODIFIERKEY_RIGHT_SHIFT)  {
+    mod_shift_r = m_key;
+  }
+  else if (m_key == MODIFIERKEY_LEFT_CTRL)  {
+    mod_ctrl_l = m_key;
+  }
+  else if (m_key == MODIFIERKEY_RIGHT_CTRL)  {
+    mod_ctrl_r = m_key;
+  }
+  else if (m_key == MODIFIERKEY_LEFT_ALT)  {
+    mod_alt_l = m_key;
+  }
+  else if (m_key == MODIFIERKEY_RIGHT_ALT)  {
+    mod_alt_r = m_key;
+  }
+  else if (m_key == MODIFIERKEY_GUI)  {
+    mod_gui = m_key;
+  }
+}
+//
+// Function to load 0 into the appropriate mod variable
+void clear_mod(int m_key) {
+  if (m_key == MODIFIERKEY_LEFT_SHIFT)  {
+    mod_shift_l = 0;
+  }
+  else if (m_key == MODIFIERKEY_RIGHT_SHIFT)  {
+    mod_shift_r = 0;
+  }
+  else if (m_key == MODIFIERKEY_LEFT_CTRL)  {
+    mod_ctrl_l = 0;
+  }
+  else if (m_key == MODIFIERKEY_RIGHT_CTRL)  {
+    mod_ctrl_r = 0;
+  }
+  else if (m_key == MODIFIERKEY_LEFT_ALT)  {
+    mod_alt_l = 0;
+  }
+  else if (m_key == MODIFIERKEY_RIGHT_ALT)  {
+    mod_alt_r = 0;
+  }
+  else if (m_key == MODIFIERKEY_GUI)  {
+    mod_gui = 0;
+  }
+}
+//
+// Function to send the modifier keys over usb
+void send_mod() {
+  Keyboard.set_modifier(mod_shift_l | mod_shift_r | mod_ctrl_l | mod_ctrl_r | mod_alt_l | mod_alt_r | mod_gui);
+  Keyboard.send_now();
+}
+//
+// Function to send the normal keys in the 6 slots over usb
+void send_normals() {
+  Keyboard.set_key1(slot1);
+  Keyboard.set_key2(slot2);
+  Keyboard.set_key3(slot3);
+  Keyboard.set_key4(slot4);
+  Keyboard.set_key5(slot5);
+  Keyboard.set_key6(slot6);
+  Keyboard.send_now();
+}
+//
+// Function to set a pin to high impedance (acts like open drain output)
+void go_z(int pin)
+{
+  pinMode(pin, INPUT);
+  digitalWrite(pin, HIGH);
+}
+//
+// Function to set a pin as an input with a pullup
+void go_pu(int pin)
+{
+  pinMode(pin, INPUT_PULLUP);
+  digitalWrite(pin, HIGH);
+}
+//
+// Function to send a pin to a logic low
+void go_0(int pin)
+{
+  pinMode(pin, OUTPUT);
+  digitalWrite(pin, LOW);
+}
+//
+// Function to send a pin to a logic high
+void go_1(int pin)
+{
+  pinMode(pin, OUTPUT);
+  digitalWrite(pin, HIGH);
+}
+//
+//----------------------------------Setup-------------------------------------------
+void setup() {
+
+  for (int a = 0; a < cols_max; a++) {  // loop thru all column pins 
+    go_pu(Col_IO[a]); // set each column pin as an input with a pullup
+  }
+//
+  for (int b = 0; b < rows_max; b++) {  // loop thru all row pins 
+    go_z(Row_IO[b]); // set each row pin as a floating output
+  }  
+}
+//
+boolean Fn_pressed = HIGH; // Initialize Fn key to HIGH = "not pressed"
+// extern volatile uint8_t keyboard_leds; // 8 bits sent from Pi to Teensy that give keyboard LED status. Caps lock is bit D1.
+//
+//---------------------------------Main Loop---------------------------------------------
+//
+void loop() { 
+  // Scan keyboard matrix with an outer loop that drives each row low and an inner loop that reads every column (with pull ups).
+  // The routine looks at each key's present state (by reading the column input pin) and also the previous state from the last scan
+  // that was 30msec ago. The status of a key that was just pressed or just released is sent over USB and the state is saved in the old_key matrix. 
+  // The keyboard keys will read as logic low if they are pressed (negative logic).
+  // The old_key matrix also uses negative logic (low=pressed). 
+  //
+  for (int x = 0; x < rows_max; x++) {   // loop thru the rows
+    go_0(Row_IO[x]); // Activate Row (send it low)
+    delayMicroseconds(10); // give the row time to go low and settle out
+    for (int y = 0; y < cols_max; y++) {   // loop thru the columns
+      // **********Modifier keys including the Fn special case
+      if (modifier[x][y] != 0) {  // check if modifier key exists at this location in the array (a non-zero value)
+        if (!digitalRead(Col_IO[y]) && (old_key[x][y])) {  // Read column to see if key is low (pressed) and was previously not pressed
+          if (modifier[x][y] != MODIFIERKEY_FN) {   // Exclude Fn modifier key  
+            load_mod(modifier[x][y]); // function reads which modifier key is pressed and loads it into the appropriate mod_... variable   
+            send_mod(); // function sends the state of all modifier keys over usb including the one that just got pressed
+            old_key[x][y] = LOW; // Save state of key as "pressed"
+          }
+          else {   
+            Fn_pressed = LOW; // Fn status variable is active low
+            old_key[x][y] = LOW; // old_key state is "pressed" (active low)
+          }
+        }
+        else if (digitalRead(Col_IO[y]) && (!old_key[x][y])) {  //check if key is not pressed and was previously pressed
+          if (modifier[x][y] != MODIFIERKEY_FN) { // Exclude Fn modifier key 
+            clear_mod(modifier[x][y]); // function reads which modifier key was released and loads 0 into the appropriate mod_... variable
+            send_mod(); // function sends all mod's over usb including the one that just released
+            old_key[x][y] = HIGH; // Save state of key as "not pressed"
+          }
+          else {
+            Fn_pressed = HIGH; // Fn is no longer active
+            old_key[x][y] = HIGH; // old_key state is "not pressed" 
+          }
+        }
+      } 
+      // ***********end of modifier section
+      //
+      // ***********Normal keys and media keys in this section
+      else if ((normal[x][y] != 0) || (media[x][y] != 0)) {  // check if normal or media key exists at this location in the array
+        if (!digitalRead(Col_IO[y]) && (old_key[x][y]) && (!slots_full)) { // check if key is pressed and was not previously pressed and slots not full
+          old_key[x][y] = LOW; // Save state of key as "pressed"
+          if (Fn_pressed) {  // Fn_pressed is active low so it is not pressed and normal key needs to be sent
+            // **** SPECIAL for < and > which are not supported ****
+            // If the < key is pressed and also one between left or right shift is pressed
+            if(normal[x][y] == KEY_NON_US_100 && (mod_shift_l == MODIFIERKEY_LEFT_SHIFT || mod_shift_r == MODIFIERKEY_RIGHT_SHIFT)) {
+              Keyboard.press('>'); // > literal is sent using keyboard press function
+              delay(5); // delay 5 milliseconds before releasing to make sure it gets sent over USB
+              Keyboard.release('>'); // send key release
+            }
+            // If only < is pressed
+            else if (normal[x][y] == KEY_NON_US_100) {
+              Keyboard.press('<'); // < literal is sent using keyboard press function
+              delay(5); // delay 5 milliseconds before releasing to make sure it gets sent over USB
+              Keyboard.release('<'); // send key release
+            }
+            // All the other normal keys
+            else {
+              load_slot(normal[x][y]); //update first available slot with normal key name
+              send_normals(); // send all slots over USB including the key that just got pressed 
+            }
+          }
+          else if (media[x][y] != 0) { // Fn is pressed so send media if a key exists in the matrix
+            Keyboard.press(media[x][y]); // media key is sent using keyboard press function per PJRC
+            delay(5); // delay 5 milliseconds before releasing to make sure it gets sent over USB
+            Keyboard.release(media[x][y]); // send media key release
+          }
+        }          
+        else if (digitalRead(Col_IO[y]) && (!old_key[x][y])) { //check if key is not pressed, but was previously pressed 
+          old_key[x][y] = HIGH; // Save state of key as "not pressed"
+          if (Fn_pressed) {  // Fn is not pressed
+            clear_slot(normal[x][y]); //clear the slot that contains the normal key name
+            send_normals(); // send all slots over USB including the key that was just released 
+          }
+        }
+      } 
+    // **************end of normal and media key section 
+    }
+    go_z(Row_IO[x]); // De-activate Row (send it to hi-z)
+  }
+  //
+  // **********keyboard scan complete
+  delay(25); // The overall keyboard scanning rate is about 30ms
+}
diff --git a/Example_Keyboards/HP_ZV6000/Keyboard pic.jpg b/Example_Keyboards/HP_ZV6000/Keyboard pic.jpg
new file mode 100644
index 0000000..986340e
Binary files /dev/null and b/Example_Keyboards/HP_ZV6000/Keyboard pic.jpg differ
diff --git a/Example_Keyboards/HP_ZV6000/Keyboard_without_number_pad specialkeys.txt b/Example_Keyboards/HP_ZV6000/Keyboard_without_number_pad specialkeys.txt
new file mode 100644
index 0000000..428b812
--- /dev/null
+++ b/Example_Keyboards/HP_ZV6000/Keyboard_without_number_pad specialkeys.txt	
@@ -0,0 +1,94 @@
+MODIFIERKEY_LEFT_CTRL	7	8	
+MODIFIERKEY_RIGHT_CTRL	5	7	
+MODIFIERKEY_LEFT_SHIFT	6	4	
+MODIFIERKEY_RIGHT_SHIFT	2	4	
+MODIFIERKEY_LEFT_ALT	3	20	
+MODIFIERKEY_RIGHT_ALT	12	20	
+MODIFIERKEY_GUI	1	18		
+KEY_A	5	11	
+KEY_B	12	14	
+KEY_C	6	13	
+KEY_D	5	13	
+KEY_E	2	13	
+KEY_F	5	14	
+KEY_G	1	14	
+KEY_H	1	16	
+KEY_I	2	17	
+KEY_J	5	16	
+KEY_K	5	17	
+KEY_L	5	22	
+KEY_M	6	16	
+KEY_N	12	16	
+KEY_O	2	22	
+KEY_P	2	23	
+KEY_Q	2	11	
+KEY_R	2	14	
+KEY_S	5	10	
+KEY_T	8	14	
+KEY_U	2	16	
+KEY_V	14	6	
+KEY_W	10	2	
+KEY_X	6	10	
+KEY_Y	8	16	
+KEY_Z	6	11		
+KEY_1	3	11	
+KEY_2	10	3	
+KEY_3	3	13	
+KEY_4	3	14	
+KEY_5	9	14	
+KEY_6	9	16	
+KEY_7	3	16	
+KEY_8	3	17	
+KEY_9	3	22	
+KEY_0	3	23	
+KEY_BACKSPACE	1	21	
+KEY_ESC	11	1	
+KEY_F1	12	13	
+KEY_F2	9	13	
+KEY_F3	13	8	
+KEY_F4	13	10	
+KEY_F5	9	10	
+KEY_F6	8	10	
+KEY_F7	1	10	
+KEY_F8	10	12	
+KEY_F9	9	22	
+KEY_F10	22	8	
+KEY_F11	22	1	
+KEY_F12	12	22		
+KEY_DELETE	12	24	
+KEY_PAGE_UP	9	24	
+KEY_PAGE_DOWN	5	24	
+KEY_END	24	6	
+KEY_RIGHT	3	24	
+KEY_LEFT	2	24	
+KEY_UP		2	21	
+KEY_DOWN	21	3	
+KEY_MENU	9	19	
+KEY_PERIOD	6	22	
+KEY_COMMA	6	17				
+KEY_ENTER	21	5		
+KEY_CAPS_LOCK	11	12	
+KEY_TAB	8	11	
+KEY_SPACE	6	21
+KEY_HOME	8	24
+KEY_INSERT	1	24
+MODIFIERKEY_FN	9	15
+
+WORKING
+ALL KEYS ABOVE
+CTRL/SHIFT/ALT COMBINATIONS
+
+NOT WORKING
+FN COMBINATIONS
+\	9	11	
+-	6	23	
+ò	5	23	
+à	1	23	
+ù	9	21	
+è	8	23	
++	8	17	
+<	9	17	
+'	9	23	
+ì	12	23	
+SCORR	1	17	
+PAUSA	12	21	
diff --git a/Example_Keyboards/HP_ZV6000/Keyboard_without_number_pad.txt b/Example_Keyboards/HP_ZV6000/Keyboard_without_number_pad.txt
new file mode 100644
index 0000000..5ba192b
--- /dev/null
+++ b/Example_Keyboards/HP_ZV6000/Keyboard_without_number_pad.txt
@@ -0,0 +1,98 @@
+MODIFIERKEY_LEFT_CTRL	7	8	
+MODIFIERKEY_RIGHT_CTRL	5	7	
+MODIFIERKEY_LEFT_SHIFT	6	4	
+MODIFIERKEY_RIGHT_SHIFT	2	4	
+MODIFIERKEY_LEFT_ALT	3	20	
+MODIFIERKEY_RIGHT_ALT	12	20	
+MODIFIERKEY_GUI	1	18	
+MODIFIERKEY_FN	9	15	
+KEY_A	5	11	
+KEY_B	12	14	
+KEY_C	6	13	
+KEY_D	5	13	
+KEY_E	2	13	
+KEY_F	5	14	
+KEY_G	1	14	
+KEY_H	1	16	
+KEY_I	2	17	
+KEY_J	5	16	
+KEY_K	5	17	
+KEY_L	5	22	
+KEY_M	6	16	
+KEY_N	12	16	
+KEY_O	2	22	
+KEY_P	2	23	
+KEY_Q	2	11	
+KEY_R	2	14	
+KEY_S	5	10	
+KEY_T	8	14	
+KEY_U	2	16	
+KEY_V	14	6	
+KEY_W	10	2	
+KEY_X	6	10	
+KEY_Y	8	16	
+KEY_Z	6	11		
+KEY_1	3	11	
+KEY_2	10	3	
+KEY_3	3	13	
+KEY_4	3	14	
+KEY_5	9	14	
+KEY_6	9	16	
+KEY_7	3	16	
+KEY_8	3	17	
+KEY_9	3	22	
+KEY_0	3	23	
+KEY_MINUS	6	23		
+KEY_BACKSPACE	1	21	
+KEY_ESC	11	1	
+KEY_F1	12	13	
+KEY_F2	9	13	
+KEY_F3	13	8	
+KEY_F4	13	1	
+KEY_F5	9	10	
+KEY_F6	8	10	
+KEY_F7	1	10	
+KEY_F8	10	12	
+KEY_F9	9	22	
+KEY_F10	22	8	
+KEY_F11	22	1	
+KEY_F12	12	22	
+KEY_INSERT	1	24	
+KEY_DELETE	12	24	
+KEY_HOME	8	24	
+KEY_PAGE_UP	9	24	
+KEY_PAGE_DOWN	5	24	
+KEY_END	24	6	
+KEY_RIGHT	3	24	
+KEY_LEFT	2	24	
+KEY_UP		2	21	
+KEY_DOWN	21	3	
+KEY_MENU	9	19	
+KEY_SLASH	
+KEY_PERIOD	6	22	
+KEY_COMMA	6	17		
+KEY_SEMICOLON		
+KEY_QUOTE	9	23	
+KEY_ENTER	21	5	
+KEY_LEFT_BRACE	
+KEY_RIGHT_BRACE	
+KEY_BACKSLASH	11	9	
+KEY_CAPS_LOCK	11	12	
+KEY_TAB	8	11	
+KEY_SPACE	6	21	
+KEY_PRINTSCREEN	
+KEY_NUM_LOCK	17	1	
+KEY_MEDIA_PLAY	FN	
+KEY_MEDIA_PAUSE	FN	
+KEY_MEDIA_RECORD	FN	
+KEY_MEDIA_STOP	FN	
+KEY_MEDIA_REWIND	FN	
+KEY_MEDIA_FAST_FORWARD	FN	
+KEY_MEDIA_PREV_TRACK	FN	
+KEY_MEDIA_NEXT_TRACK	FN	
+KEY_MEDIA_VOLUME_DEC	FN	
+KEY_MEDIA_VOLUME_INC	FN	
+KEY_MEDIA_PLAY_PAUSE	FN	
+KEY_MEDIA_PLAY_SKIP	FN	
+KEY_MEDIA_MUTE	FN	
+KEY_MEDIA_EJECT	FN	
diff --git a/Example_Keyboards/HP_ZV6000/python_results_LC b/Example_Keyboards/HP_ZV6000/python_results_LC
new file mode 100644
index 0000000..8c94c8c
--- /dev/null
+++ b/Example_Keyboards/HP_ZV6000/python_results_LC
@@ -0,0 +1,106 @@
+initial outputpin:7
+-----------------------------------------------------
+Results:
+-----------------------------------------------------
+FPC PINS:
+
+8 inputpins:
+[1, 2, 3, 5, 6, 8, 9, 12]
+
+16 outputpins:
+[4, 7, 10, 11, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24]
+-----------------------------------------------------
+TEENSY PINS (these have to be copied to the arduino file):
+
+8 inputpins:
+[23, 0, 22, 24, 2, 3, 25, 5]
+
+16 outputpins:
+[1, 21, 4, 20, 19, 6, 18, 7, 17, 8, 16, 9, 15, 10, 14, 11]
+-----------------------------------------------------
+Copy these matrices into the Arduino USB Controller code
+
+-----------------------------------------------------
+KEY
+-----------------------------------------------------
+{
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{KEY_F7,KEY_W,KEY_2,KEY_S,KEY_X,KEY_F6,KEY_F5,KEY_F8},
+{KEY_ESC,KEY_Q,KEY_1,KEY_A,KEY_Z,KEY_TAB,KEY_BACKSLASH,KEY_CAPS_LOCK},
+{KEY_F4,KEY_E,KEY_3,KEY_D,KEY_C,KEY_F3,KEY_F2,KEY_F1},
+{KEY_G,KEY_R,KEY_4,KEY_F,KEY_V,KEY_T,KEY_5,KEY_B},
+{0,0,0,0,0,0,0,0},
+{KEY_H,KEY_U,KEY_7,KEY_J,KEY_M,KEY_Y,KEY_6,KEY_N},
+{KEY_NUM_LOCK,KEY_I,KEY_8,KEY_K,KEY_COMMA,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,KEY_MENU,0},
+{0,0,0,0,0,0,0,0},
+{KEY_BACKSPACE,KEY_UP,KEY_DOWN,KEY_ENTER,KEY_SPACE,0,0,0},
+{KEY_F11,KEY_O,KEY_9,KEY_L,KEY_PERIOD,KEY_F10,KEY_F9,KEY_F12},
+{0,KEY_P,KEY_0,0,KEY_MINUS,0,KEY_QUOTE,0},
+{KEY_INSERT,KEY_LEFT,KEY_RIGHT,KEY_PAGE_DOWN,KEY_END,KEY_HOME,KEY_PAGE_UP,KEY_DELETE},
+}
+-----------------------------------------------------
+MODIFIER
+-----------------------------------------------------
+{
+{0,MODIFIERKEY_RIGHT_SHIFT,0,0,MODIFIERKEY_LEFT_SHIFT,0,0,0},
+{0,0,0,MODIFIERKEY_RIGHT_CTRL,0,MODIFIERKEY_LEFT_CTRL,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,MODIFIERKEY_FN,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{MODIFIERKEY_GUI,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,MODIFIERKEY_LEFT_ALT,0,0,0,0,MODIFIERKEY_RIGHT_ALT},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+}
+-----------------------------------------------------
+FN
+-----------------------------------------------------
+{
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+{0,0,0,0,0,0,0,0},
+}
+-----------------------------------------------------
+ONE
+-----------------------------------------------------
+{
+{1,1,1,1,1,1,1,1},
+{1,1,1,1,1,1,1,1},
+{1,1,1,1,1,1,1,1},
+{1,1,1,1,1,1,1,1},
+{1,1,1,1,1,1,1,1},
+{1,1,1,1,1,1,1,1},
+{1,1,1,1,1,1,1,1},
+{1,1,1,1,1,1,1,1},
+{1,1,1,1,1,1,1,1},
+{1,1,1,1,1,1,1,1},
+{1,1,1,1,1,1,1,1},
+{1,1,1,1,1,1,1,1},
+{1,1,1,1,1,1,1,1},
+{1,1,1,1,1,1,1,1},
+{1,1,1,1,1,1,1,1},
+{1,1,1,1,1,1,1,1},
+}